|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | A pathway to improve low-cycle fatigue life of face-centered cubic metals via grain boundary engineering显示文摘To probe a pathway to improve the low-cycle fatigue life of face-centered cubic(FCC)metals via grain boundary engineering(GBE),the tension-tension fatigue tests were carried out on the non-GBE and GBE Cu-16 at.%Al alloys at relatively high stress amplitudes.The results indicate that the cyclic strain localiza-tion and cracking at grain boundaries(GBs)can be effectively suppressed,especially at increased stress amplitude,by an appropriate GBE treatment that can result in a higher resistance to GB cracking and a greater capability of compatible deformation.Therefore,the sensitivity of fatigue life to stress amplitude can be weakened by GBE,and the low-cycle fatigue life of Cu-16 at.%Al alloys is thus distinctly improved. | X.J.Guan Z.P.Jia S.M.Liang F.Shi X.W.Li | 2022 | Journal of Materials Science & Technology2022，，18： | 0 |
| 2 | Effect of Grain Boundary Engineering on the Work Hardening Behavior of AL6XN Super‑Austenitic Stainless Steel显示文摘To examine the influence of grain boundary engineering(GBE)on the work hardening behavior,the tensile tests were carried out on the non-GBE and GBE AL6XN super-austenitic stainless steel(ASS)samples with a comparable grain size at two strain rates of 10^(-2)s^(-1)and 10^(-4)s^(-1).The evolution of deformation microstructures was revealed by transmission electron microscopy(TEM)and quasi-in situ electron backscatter diffraction(EBSD)observations.The results show that the influence of GBE on the mechanical properties of AL6XN super-ASS is mainly manifested in the change of work hardening behavior.At the early stage of plastic deformation,GBE samples show a slightly lowered work hardening rate,since the special grain boundaries(SBs)of a high fraction induce a higher dislocation free path and a weaker back stress;however,with increasing plastic deformation amount,the work hardening rate of GBE samples gradually surpasses that of non-GBE samples due to the better capacity of maintainable work hardening that is profited from the inhibited dislocation annihilation by SBs.In a word,the enhanced capacity of sustained work hardening effectively postpones the appearance of necking point and thus efficaciously ameliorates the ductility of GBE samples under the premise of little changes in yield strength and ultimate tensile strength. | X.J.Guan Z.P.Jia M.A.Nozzari Varkani X.W.Li | 2023 | Acta Metallurgica Sinica(English Letters)2023，36，4： | 0 |
| 3 | Improving Intergranular Stress Corrosion Cracking Resistance in a Fe–18Cr–17Mn–2Mo–0.85N Austenitic Stainless Steel Through Grain Boundary Character Distribution Optimization显示文摘The grain boundary character distribution(GBCD) optimization and its effect on the intergranular stress corrosion cracking(IGSCC) resistance in a cold-rolled and subsequently annealed Fe-18 Cr-17 Mn-2 Mo-0.85 N high-nitrogen nickel-free austenitic stainless steel were systematically explored.The results show that stacking faults and planar slip bands appearing at the right amount of deformation(lower than 10%) are beneficial cold-rolled microstructures to the GBCD optimization.The proportion of special boundaries gradually increases in the subsequent stages of recrystallization and grain growth,accompanying with the growth of twin-related domain in the experimental steel.In this way,the fraction of low ∑ coincidence site lattice(CSL) boundaries can reach as high as 82.85% for the specimen cold-rolled by 5% and then annealed at 1423 K for 72 h.After GBCD optimization,low ∑ CSL boundaries and the special triple junctions(J2,J3) of high proportion can greatly hinder the nitride precipitation along grain boundaries and enhance the capability for intergranular crack arrest,thus improving the IGSCC resistance of the experimental steel. | F.Shi L.Yan J.Hu L.F.Wang T.Z.Li W.Li X.J.Guan C.M.Liu X.W.Li | 2022 | Acta Metallurgica Sinica(English Letters)2022，35，11： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员